Electrical Code Requirements for Rooms

Electrical codes are intended for protecting homeowners and home residents. These basic rules will give you the concepts of what electrical inspectors are looking for when they review both remodeling projects and new installations. Most local codes are based on the National Electrical Code (NEC), a document that lays out required practices for all aspects of residential and commercial electrical application. The NEC is usually revised every three years—2014, 2017 and so forth—and occasionally there are important changes to the Code. Please make sure that your sources of information are always based on the most recent Code. The code requirements listed here are based on the 2017 version.

Most local codes are following the NEC, but there can be differences. The local code always enjoys priority over the NEC when there are differences, so please make sure to check with your local building department for the specific code requirements for your situation.

Many of the NEC involves requirements for general electrical installation that apply to all situations, however, there are also specific requirements for individual rooms. 

Electrical Codes?

Electrical codes are rules or laws that dictate how electrical wiring will be installed in residences. They are used for safety and can vary for different rooms. Obviously, electrical codes follow the National Electrical Code (NEC), but local codes should be followed first and foremost.

Kitchen

The kitchen uses the most electricity compared with any rooms in the house. About fifty years ago, a kitchen might have been served by a single electrical circuit, but now, a newly installed kitchen with standard appliances requires at least seven circuits and even more.

• Kitchens must have at least two 20-amp 120-volt ”small appliance” circuits serving the receptacles in the countertop areas. These are for portable plug-in appliances.
• An electric range/oven requires its own dedicated 120/240-volt circuit.
• The dishwasher and garbage disposal both require their own dedicated 120-volt circuits. These can be 15-amp or 20-amp circuits, depending on the electrical load of the appliance (check the manufacturer’s recommendations; usually 15-amps is sufficient). The dishwasher circuit requires GFCI protection, but the garbage disposal circuit does not—unless the manufacturer stipulates it. 
• The refrigerator and microwave each require their own dedicated 120-volt circuits. The amperage rating should be appropriate to the electrical load of the appliance; these should be 20-amp circuits. 
• All countertop receptacles and any receptacle within 6 feet of a sink must be GFCI-protected. The countertop receptacles should be spaced no more than 4 feet apart. 
• Kitchen lighting must be supplied by a separate 15-amp (minimum) circuit.

Bathrooms

Current bathrooms have very carefully defined requirements because of the presence of water. With their lights, vent fans, and outlets that may power hairdryers and other appliances, bathrooms use a lot of power and may need more than one circuit.

• The outlet receptacles must be served by a 20-amp circuit. The same circuit can supply the entire bathroom (outlets plus lighting), provided there are no heaters (including vent fans with built-in heaters) and provided the circuit serves only a single bathroom and no other areas. Alternatively, there should be a 20-amp circuit for the receptacles only, plus a 15- or 20-amp circuit for the lighting. 
• Vent fans with built-in heaters must be on their own dedicated 20-amp circuits.
• All electrical receptacles in bathrooms must have ground-fault circuit-interrupter (GFCI) for protection. 
• A bathroom requires at least one 120-volt receptacle within 3 feet of the outside edge of each sink basin. Duel sinks can be served by a single receptacle positioned between them.
• Light fixtures in the shower or bath area must be rated for damp locations unless they are subject to shower spray, in which case they must be rated for wet locations.

Living Room, Dining Room, and Bedrooms

Standard living areas are relatively modest power users, but they have clearly indicated electrical requirements. These areas are generally served by standard 120-volt 15-amp or 20-amp circuits that may serve not only one room. 

• These rooms require that a wall switch is placed beside the entry door of the room so that you can light the room upon entering it. This switch can control either a ceiling light, a wall light, or a receptacle for plugging in a lamp. The ceiling fixture must be controlled by a wall switch rather than a pull chain.
• Wall receptacles may be placed no farther than 12 feet apart on any wall surface. Any wall section wider than 2 feet must have a receptacle.
• Dining rooms usually require a separate 20-amp circuit for one outlet used for a microwave, entertainment center, or window air conditioner.

Stairways

Special caution is required in stairways to ensure all of the steps are lighted properly to reduce the possibility of failing and minimize the hazard caused.

• Three-way switches are needed at the top and bottom of each flight of stairs so that lights can be turned on and off from both ends. 
• If the stairs turn at a landing, you may need to add additional lighting fixtures to make sure all areas are illuminated. 

Hallways

The areas of hallways can be long and need adequate ceiling lighting. Make sure to place enough lighting so shadows are not cast when walking. Keep in mind hallways often serve as escape routes in the event of emergencies.

• A hallway over 10 feet long is required to have an outlet for general purpose use.
• Three-way switches are required at each end of the hallway, allowing the ceiling light to be turned on and off from both ends. 
• If there are more doors served by a hallway, such as for a bedroom or two, you probably want to add a four-way switch near the door outside of each room.

Closets

Closets need to follow many rules regarding fixture type and placement.

• Fixtures with incandescent light bulbs (usually get very hot) must be enclosed with a globe or cover and cannot be installed within 12 inches of any clothes storage areas (or 6 inches for recessed fixtures).
• Fixtures with LED bulbs have to be at least 12 inches far from storage areas (or 6 inches for recessed).
• Fixtures with CFL (compact fluorescent) bulbs may be placed within 6 inches of storage areas.
• All surface-mounted (not recessed) fixtures must be on the ceiling or the wall above the door.

Laundry Room

The electrical needs of a laundry room will be different, it depends on if the clothes dryer is electric or gas.

• A laundry room needs at least one 20-amp circuit for receptacles serving laundry equipment; this circuit can supply a clothes washer or a gas dryer.
• An electric dryer needs its own 30-amp, 240-volt circuit wired with four conductors (older circuits often have three conductors).
• All receptacles have to be GFCI-protected.

Garage

As of the 2017 NEC, newly constructed garages need at least one dedicated 120-volt 20-amp circuit to serve only the garage. This circuit probably power receptacles mounted on the exterior of the garage as well. 

• Inside the garage, there should be at least one switch for light controlling. It is recommended to install three-way switches for convenience between the doors.
• Garages must have one receptacle at least, including one for each car space.
• All garage receptacles must be GFCI-protected.

Additional Requirements

AFCI requirements. The NEC requires that virtually all branch circuits for lighting and receptacles in a home must have arc-fault circuit-interrupter (AFCI) protection. This is a form of protection that guards against sparking (arcing) and thereby reduces the chance of fire. Note that the AFCI requirement is in addition to whatever GFCI protection is required—an AFCI does not replace or eliminate the need for GFCI protection. 

AFCI requirements are enforced mostly in new construction—there is no requirement that an existing system must be updated to comply with new-construction AFCI requirements. However, as of the 2017 NEC revision, when homeowners or electricians update or replace failing receptacles or other devices, they are required to add the AFCI protection at that location.  This can be done in several ways: 

• A standard circuit breaker can be replaced with a special AFCI circuit breaker. This is a job for a licensed electrician. Doing so will create AFCI protection for the entire circuit. 
• A failing receptacle can be replaced with an AFCI receptacle. This will provide AFCI protection for only the receptacle that is being replaced. 
• Where GFCI protection is also required (such as kitchens and bathrooms), a receptacle can be replaced with a dual AFCI/GFCI receptacle. 

Tamper resistant receptacles. All standard receptacles must be tamper-resistant (TR) type. This is designed with a built-in safety feature that prevents children from sticking items into the receptacle slots.